DRAY SEC

Impermeable mortar for concrete and masonry.


It is a mortar of plastic and ductile consistence.
It’s easy to apply, with a great power to seal off fissures and pores and excellent adherence.
It hardens without fissures.
It’s applicable in thickness till 5mm.
It’s impermeable and at the same time perspirable.

Uses

It is applied where there is humidity from superficial water or underground filtrations. DRAY SEC is used, in walls, façades, foundations, tanks, swimming-pools, silos, pavements, gardens, etc.

Surface preparation

The surface must be clean of paints, greases, oils, dust, etc; moreover of being firm and hard.
The surfaces to waterproof must be perfectly wet when DRY SEC is applied to achieve a good anchorage. Protect the coatings from draught air and direct sun. Do not apply with temperatures below 5ºC.

Instructions for use

Amass the product with water at the moment of its application. Depending on the surface the product will be applied with brush, paintbrush, paint roller or trowel.
When more than one coat is applied it is necessary to wet the surfaces among coats to form perfect union. To repair big holes or half-pipes DRAY SEC can be mixed with two parts of quartz sand with sand gradation between 0.1and 3 mm.

Consumption

Consumption approximate, depending on the state of the surface.
- Superficial water and filtrations without pressure: 2 Kg/m².
- Water with pressure:4 Kg/m².
- When the water filtrations are continuous, apply HIPERDRAI V to block the leaking previously and then DRAY SEC to seal it off.
- Application time at 20ºC: 3 hours approx.
- Stiffening time at 20ºC: 10 hours approx.
- Total hard at 20ºC: 7 days approx.

Colours

Grey.

Packing and storing

DRYSEC is packed in hermetic barrels, according to EC packing and storing directives for chemical products. The usual security measures when using cement based products.

Hygiene and safety

Use protective gloves.

Specification

Aspect: homogeneous grey powder.
Density (g/ml):Apparent: 1.15±0, 05
Humidity: 1, 84±0, 05
Sand Gradation: Sieve: 0,63mm: 7±3%
0,315mm: 13±5%
0,16mm: 31±10%
Depth: 55±10%
Compression: 3 days: 118,8kg/cm2
7 days: 158, 3 kg/cm2
Dry: to touch: 1≤ 2 hours
Total: 12≤ 24 hours
Registered in the health and food General Register for the manufacture and/or production and/or transformation of varnish paints and covers Nº Register 39.03631/GE.


Notes:

- La presente ficha técnica sirve, al igual que todas las demás recomendaciones e información técnica, únicamente para la descripción de las características del producto, forma de empleo y su aplicaciones. Los datos e informaciones reproducidas se basan en nuestros conocimientos técnicos obtenidos en bibliografia, en ensayos de laboratorio y en la práctica.
- Los datos sobre consumo y dosificación que figuran en esta ficha técnica se basan en nuestra propia experiencia, por lo que estos son susceptibles de variaciones debido a las diferentes condiciones de las obras. Los consumos y dosificaciones reales deberán determinarse en la obra mediante ensayos previos y son responsabilidad del cliente.
- Para un asesoramiento adicional, nuestro Departamento de Química Aplicada para la Construcción, está a su disposición.
- Otras aplicaciones del producto que no se ajusten a las indicadas, no serán de nuestra responsabilidad.
- Otorgamos garantía en caso de defectos en la calidad de fabricación de nuestros productos, quedando excluidas las reclamaciones adicionales, siendo de nuestra responsabilidad tan sólo la de reingresar el valor de la mercancía suministrada.
- Deben tenerse en cuenta las eventuales reservas correspondientes a patentes o derechos de terceros.
- La presente ficha técnica pierde su validez con la aplicación de una nueva edición.