Products

It has a non-slippery finished and is unalterable to acids and alkalis coating. PIEPOX is a product entirely developed in our laboratories for coatings which needs a high resistance degree against chemical agents and to abrasion. PIEPOX has a high resistance to impacts, to friction and to chemical products.

· Uses
· Surface preparation
· Instructions for use
· Consumption
· Colours
· Packing and storing
· Hygiene and safety
· Specification

Last update: 06/11/2008

Uses

PIEPOX gives a unique quality, within its antacid covering range in: all kinds of industrial floors,
Residual water tanks, industrial installations, tanned leather factories, sports facilities, garages, car-parks, etc.

Surface preparation

On new surfaces which have never been painted, it is recommended to apply a preparation coat of prime with our product PRIMA-68. The rest of the surfaces must be clean, dry and exempt of greases, oils and other impurities which could affect the normal paint adherence. When the surface is made of concrete or mortar it must be slightly rough, and if it is newly made, it is recommended to use a wood or felt trowel, but never with a metallic trowel. If the floor is too smooth or it has cement whitewashes, scrap off or mill the surface with plenty of water and sand.

Instructions for use

Mix the two components, are supplied in separate packages, in the adequate proportion (add the solidifier – the small container- into the base – the big container-) and mix intensely until you achieve a uniform mixture (mix it with mechanical low revolution mixer – 500rpm- during 3 minutes). If its necessary, DILUYENTE Nº2 to adjust the viscosity. Remember that the “POT LIFE” or usable mixer time depends on the quantity and environment temperature, so it is not suitable to mix more than one set at the same time.
PIEPOX can be applied with brush, paint roller, airless or spray gun.

Consumption

5 m² per Kg and coat approximately, depending on the roughness and the porosity of the surface.
In order to determinate the consumption, mainly on surfaces extremely roughness or absorbent, it is recommended to make a previous test on a measured surface and with a previous weighted product amount.

Colours

White, red, grey and green, other colours: orders over 500 Kg.

Packing and storing

PIEPOX is supplied in prepared hermetic sets of 5 Kg, according to EC packing and storing directives for chemical products.

Hygiene and safety

See product label.

Specification

Pot life at 20ºC:3 hours
Density (A+B) 20ºC: 1, 40 g/cm³
Viscosity A+B (Brookfield, A4, V20, 20ºC):20 P.
Dry extract Part A (Auto, 120ºC): 85
Dry extract Part B (Auto, 120ºC): 47
Resistance in places with permanent moisture:-30ºC - +60ºC.
Passable in: -30ºC +100ºC
Total hardening:6 days

Notes:

- La presente ficha técnica sirve, al igual que todas las demás recomendaciones e información técnica, únicamente para la descripción de las características del producto, forma de empleo y su aplicaciones. Los datos e informaciones reproducidas se basan en nuestros conocimientos técnicos obtenidos en bibliografia, en ensayos de laboratorio y en la práctica.
- Los datos sobre consumo y dosificación que figuran en esta ficha técnica se basan en nuestra propia experiencia, por lo que estos son susceptibles de variaciones debido a las diferentes condiciones de las obras. Los consumos y dosificaciones reales deberán determinarse en la obra mediante ensayos previos y son responsabilidad del cliente.
- Para un asesoramiento adicional, nuestro Departamento de Química Aplicada para la Construcción, está a su disposición.
- Otras aplicaciones del producto que no se ajusten a las indicadas, no serán de nuestra responsabilidad.
- Otorgamos garantía en caso de defectos en la calidad de fabricación de nuestros productos, quedando excluidas las reclamaciones adicionales, siendo de nuestra responsabilidad tan sólo la de reingresar el valor de la mercancía suministrada.
- Deben tenerse en cuenta las eventuales reservas correspondientes a patentes o derechos de terceros.
- La presente ficha técnica pierde su validez con la aplicación de una nueva edición.