Antacid epoxy coating, free of solvent

It has an excellent chemical resistance to the majority of acids, bases and solvents (see chemical resistant table). Very good adherence on commonly used surfaces: metals, ceramics, concrete, fibrocement, etc. It has high mechanical resistance to compression, traction and abrasion. When it is perfectly hardened it shows a smooth, bright and completely non-stick surface.


In general it is use in food industries to protect the floors and places with constant chemical aggressions. It is recommended in lactic industries, canning industries and salting plants. It’s an antacid protector for tanks and metallic structures. It’s ideal to be applied in multilayer system, with silica sand, to obtain a compact and continuous floor with high chemical and mechanical resistance.

Surface preparation

The surface must be clean, dry and totally exempt of dust, greases and oils. It is recommended to scrape off or to mill the surface to achieve an open pore surface in order to facilitate the good adherence of the primer. To apply the product on a closed pore surface, such as tiles, ceramics, etc., consult our technical department.

Instructions for use

PIEPOX CERAMICO is supplied in sets of 5 Kg. Pour part B into part A. Ensure a homogenous mixture with a mechanical agitator of low revolutions to avoid the incorporation of air bubbles. Let the mixture to settle for 5 minutes. The pot life or the used time of the mixture is 30 minutes at 20ºC approx. The product can be applied with brush, paint roller, airless or paintbrush. The application of the following coats can be done after the “dry touch” state, and before 24 hours maximum. To apply it inside tanks it is important to control the micro-condensation (water vapour due to breathing) which could impede the adherence between different coats.


One coat of 350 microns 500g/m2.


Red, grey and green, other colours: on demand in orders over 500 Kg.

Packing and storing

PIEPOX CERAMICO is supplied in hermetic sets of 5 Kg. (A + B), according to EC packing and storing directives for chemical products. Professional use.

Hygiene and safety

See product label.


Mix relation in weight: A/B: 4/1
• Colour: Depents on colour gama
• Dry extract (auto, 120ºC): >96%
• Density: 1,50±0.05 g/ml.
• Viscosity (A4, V20, 25ºC):3000-200cP
• Dry extract (auto, 75ºC): >95%
• Density: 1,02±0.05 g/ml.
• Viscosity (A4, V20, 25ºC):610-200cP
• Dry to touch (500 microns, vidrio): 5-6h
• Total dryl (500 microns, vidrio): 12 ≤ 24h
The product is suitable for floors with roller of hard fiber. The yield of the product is 4m2/kg (200 microns) this value varies in function with the roughness of the surface or thikness of the dry film.


- La presente ficha técnica sirve, al igual que todas las demás recomendaciones e información técnica, únicamente para la descripción de las características del producto, forma de empleo y su aplicaciones. Los datos e informaciones reproducidas se basan en nuestros conocimientos técnicos obtenidos en bibliografia, en ensayos de laboratorio y en la práctica.
- Los datos sobre consumo y dosificación que figuran en esta ficha técnica se basan en nuestra propia experiencia, por lo que estos son susceptibles de variaciones debido a las diferentes condiciones de las obras. Los consumos y dosificaciones reales deberán determinarse en la obra mediante ensayos previos y son responsabilidad del cliente.
- Para un asesoramiento adicional, nuestro Departamento de Química Aplicada para la Construcción, está a su disposición.
- Otras aplicaciones del producto que no se ajusten a las indicadas, no serán de nuestra responsabilidad.
- Otorgamos garantía en caso de defectos en la calidad de fabricación de nuestros productos, quedando excluidas las reclamaciones adicionales, siendo de nuestra responsabilidad tan sólo la de reingresar el valor de la mercancía suministrada.
- Deben tenerse en cuenta las eventuales reservas correspondientes a patentes o derechos de terceros.
- La presente ficha técnica pierde su validez con la aplicación de una nueva edición.