IMPRIMACION AUTOEPOXY W

Water prime of two components


Aqueous prime of two components, based in epoxy resins of very low viscosity, that gives the product the capacity of good penetration on all different surfaces.

Uses

Adherence prime of very high capacity of penetration on surfaces such as: concrete, mortars, fibrocement, for all product range of epoxy based resins, in particular for the auto-levelled mortar AUTOEPOXY W.

Surface preparation

The surfaces to treat, must be clean (exempt of grease, oils and other possible contaminants that may effect the adherence of the product) and dry. It’s recommended to prepare the surface by mechanical means: shot-blasted or drilled, in order to obtain an open porous surface that facilitates the penetration of the prime on the surface.

Instructions for use

Component A: Base; component B: reactor or hardener agent.
Empty completely component B onto component A. Mix it with mechanical agitator of low revolutions (approx. 600 r.p.m) till obtained a perfect homogenisation.
Add water and mix it again until reached a perfect homogenisation (5 minutes minimum). The application of the mix can be done by brush or roller, but without leaving a too thick coat.
The mix proportions are: 3kg of base, 1.8kg of reactor, 1.8 kg of water.
Indications:
-do not apply in temperatures inferiors to 10ºC
-The minimum age of the concrete will be 3-4 weeks depending on the environment weather conditions.
-Apply the coat between 12-48 hours, depending on the environmental temperature.

Consumption

80-150g/m2 of IMPRIMACION AUTOEPOXY W, depending on the roughness of the surface, the type of surface, the type of tools and the type of workmanship.

Colours

Colourless

Packing and storing

The prime AUTOEPOXY W is presented in the following barrels:
Part A (BASE): 3kg
Part B (Reactor/Hardener): 1.8kg
Both barrels are hermetic, according to EC packing and storing directives for chemical products.
For its storage, maintain the product in its original barrels, well closed and keep away from bad weather.

Hygiene and safety

Epoxi Resins may effect the mucous and skin, therefore it’s recommendable to use gloves and protector glasses during its application. Further information, see product label and consult the security file.

Specification

Type: epoxy resins of two componentsPart A:
Aspect: Viscose liquid of beige colour.
Density: 1.06 ± 0.03g/cm3
Viscosity (A4,v20, 25ºC): 4500± 1000cP
Dry extract: 50.0± 3.0%
pH: 9.5 ± 0.5
Part B:
Aspect: Transparent liquid colourless
Density: 1.15 ± 0.05 g/cm3
Viscosity: (A4, v20, 25ºC): 1000 cP

Mix proportion A/B water 100:60:60
Pot life: 30-45 minutes
Dry Time: Total dry :> 24 hours.

Notes:

- La presente ficha técnica sirve, al igual que todas las demás recomendaciones e información técnica, únicamente para la descripción de las características del producto, forma de empleo y su aplicaciones. Los datos e informaciones reproducidas se basan en nuestros conocimientos técnicos obtenidos en bibliografia, en ensayos de laboratorio y en la práctica.
- Los datos sobre consumo y dosificación que figuran en esta ficha técnica se basan en nuestra propia experiencia, por lo que estos son susceptibles de variaciones debido a las diferentes condiciones de las obras. Los consumos y dosificaciones reales deberán determinarse en la obra mediante ensayos previos y son responsabilidad del cliente.
- Para un asesoramiento adicional, nuestro Departamento de Química Aplicada para la Construcción, está a su disposición.
- Otras aplicaciones del producto que no se ajusten a las indicadas, no serán de nuestra responsabilidad.
- Otorgamos garantía en caso de defectos en la calidad de fabricación de nuestros productos, quedando excluidas las reclamaciones adicionales, siendo de nuestra responsabilidad tan sólo la de reingresar el valor de la mercancía suministrada.
- Deben tenerse en cuenta las eventuales reservas correspondientes a patentes o derechos de terceros.
- La presente ficha técnica pierde su validez con la aplicación de una nueva edición.