Three-component adhesive based in epoxy resins without solvents

Epoxy resins compound of high resistance which is used to stick concrete and iron elements, plaster fillings and other kind of repairs. HORFIX is an excellent union bridge between a fresh concrete and a hardened one.


Repairing works for cisterns, tanks, structural fissures, etc. To stick concrete, iron, metallic supports which are in contact with cured concrete, beams or pillars. Furthermore it is the perfect adhesive to be used with concrete, mortar, stone, wood, iron, steel, fibrocement, etc.

Surface preparation

The surface where HORFIX will be applied must be resistant (without whitewash, dust, greases, oils or other pollutants which could affect the product adherence) and clean; so it is necessary a deep surface cleaning by mechanical (abrasion, sandblast,) or chemical (for example scaling with our product DESCAL) methods and finally a good rinse with abundant water.

Instructions for use

Components mixing: the mixture can be made by hand or through a putty knife or another tool, trying to obtain a homogeneous mixture without mixed parts stuck in the pots. The mixture proportion is 81% resin and 19% catalyst. For an easy use of the components the standard pots are supplied with the exact proportion of each one so as to make easier do the mixture in the building place.
DO NOT DIVIDE THE QUANTITIES ROUGHLY because a wrong dosage can vary completely the nature of the obtained polymer and, consequently, its properties. The Pot-life (utilization time after mixing the components) varies depending on the temperature and the quantity of the product to prepare.
Surface application: when the surface is ready and the mixture is done, the product is applied on the surface with a putty knife, brush or similar, trying to place a homogeneous and continuous coat on the surface. The quantity to be applied will vary depending on the state and the porosity of the substratum, and it will be fewer as smoother is the surface. From the application till the hardening time is off the concrete can be conditioned with new mortar. The joint have the maximum resistance in 5 or 7 days, but logically the new concrete reaches its maximum resistance in 28 days.
Prefabricated concrete: what has been explained till here is also valid to join prefabricated elements; the only thing to have into account is that the product film must be thicker (1-3 mm., to be thick enough to fill the hollows between the two surfaces).


It is approximate 0, 5- 1kg/m2 depending on the state and the surface nature.



Packing and storing

HORFIX is packed in measured hermetic sets of 1 Kg., according to EC packing and storing directives for chemical products.

Hygiene and safety

See product label.


Aspect A+B: Transparent yellowish liquid.
Density A+B:1, 07±0,02g/ml
Solidifier: 1.0 g/cm³
Viscosity A+B (A4, V20, 25ºC):950±50cP
Density A+B+C at 20ºC: 1, 23±0,02g/ml
Viscosity A+B+C (A4, V20, 25ºC): 1850±Cp
Dry extract A+B+C (at 120ºC) : >95%
Resistance to compression (UNE 83.821-92): compression: 1100kg/cm2
Flexotraction: 600kg/cm2
Traction: 120kg/cm2
Pot-life:At 25ºC: 20-25 min.
-At 20ºC: 30-35 min.
-At 10ºC: 60-70 min.
Sand Gradation: 0,63mm: 2±2%
0,32mm: 30±8%
0,16mm: 39±10%
0,08mm: 19±16%
Depth: 6±3%


- La presente ficha técnica sirve, al igual que todas las demás recomendaciones e información técnica, únicamente para la descripción de las características del producto, forma de empleo y su aplicaciones. Los datos e informaciones reproducidas se basan en nuestros conocimientos técnicos obtenidos en bibliografia, en ensayos de laboratorio y en la práctica.
- Los datos sobre consumo y dosificación que figuran en esta ficha técnica se basan en nuestra propia experiencia, por lo que estos son susceptibles de variaciones debido a las diferentes condiciones de las obras. Los consumos y dosificaciones reales deberán determinarse en la obra mediante ensayos previos y son responsabilidad del cliente.
- Para un asesoramiento adicional, nuestro Departamento de Química Aplicada para la Construcción, está a su disposición.
- Otras aplicaciones del producto que no se ajusten a las indicadas, no serán de nuestra responsabilidad.
- Otorgamos garantía en caso de defectos en la calidad de fabricación de nuestros productos, quedando excluidas las reclamaciones adicionales, siendo de nuestra responsabilidad tan sólo la de reingresar el valor de la mercancía suministrada.
- Deben tenerse en cuenta las eventuales reservas correspondientes a patentes o derechos de terceros.
- La presente ficha técnica pierde su validez con la aplicación de una nueva edición.